Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Kobayashi, Jun; Aizawa, Kosuke; Ezure, Toshiki; Nagasawa, Kazuyoshi*; Kurihara, Akikazu; Tanaka, Masaaki
JAEA-Research 2022-009, 125 Pages, 2023/01
JAEA-Research-2022-009.pdf:29.22MB
The design studies of an advanced loop-type sodium-cooled fast reactor (Advanced- SFR) have been carried out by the Japan Atomic Energy Agency (JAEA). At the core outlet, temperature fluctuations occur due to mixing of hot sodium from the fuel assembly with cold sodium from the control rod channels and radial blanket assembly. These temperature fluctuations may cause high cycle thermal fatigue around a bottom of Upper Internal Structure (UIS) located above the core. Therefore, we conducted a water experiment using a 1/3 scale 60 degree sector model that simulated the upper plenum of the advanced loop-type sodium-cooled reactor. And we proposed some countermeasures against large temperature fluctuations that occur at the bottom of the UIS. In this report, we have summarized that the effect of the countermeasure structure to mitigate the temperature fluctuation generated at the bottom of UIS is confirmed, and the Reynolds number dependency of the countermeasure structure and the characteristics of the temperature fluctuation on the control rod surface.
Kobayashi, Jun; Aizawa, Kosuke; Ezure, Toshiki; Kurihara, Akikazu; Tanaka, Masaaki
Hozengaku, 20(3), p.89 - 96, 2021/10
Hot sodium from the fuel assembly can mix with cold sodium from the control rod (CR) channel and the blanket assemblies at the bottom plate of the Upper Internal Structure (UIS) of Advanced-SFR. Temperature fluctuation due to mixing of the fluids at different temperature between the core outlet and cold channel may cause high cycle thermal fatigue on the structure around the bottom of UIS. A water experiment using a 1/3 scale 60 degree sector model simulating the upper plenum of the Advanced-SFR has been conducted to examine countermeasures for the significant temperature fluctuation generated around the bottom of UIS. We focused on the temperature fluctuations near the primary and backup control rod channels, and studied the countermeasure structure to mitigate the temperature fluctuation through temperature distribution and flow velocity distribution measurements. As a result, effectiveness of the countermeasure to mitigate the temperature fluctuation intensity was confirmed.
Kobayashi, Jun; Aizawa, Kosuke; Ezure, Toshiki; Kurihara, Akikazu; Tanaka, Masaaki
Hozengaku, 20(3), p.97 - 101, 2021/10
Focusing on the thermal striping phenomena that occurs at a bottom of the internal structure of an advanced sodium-cooled fast reactor (Advanced-SFR) that has been designed by the Japan Atomic Energy Agency, a water experiment using a 1/3 scale 60 degree sector model simulating the upper plenum of the Advanced-SFR has been conducted to examine countermeasures for the significant temperature fluctuation generated around the bottom of Upper Internal Structure (UIS). In the previous paper, we reported the effect of measures to mitigate temperature fluctuations around the control rod channels. In this paper, the same test section was used, and a water experiment was conducted to obtain the characteristics of temperature fluctuations around the radial blanket fuel assembly. And the shape of the Core Instrumentation Support Plate (CIP) was modified, and it was confirmed that it was highly effective in alleviating temperature fluctuations around the radial blanket fuel assembly.
Takada, Shoji; Sekita, Kenji; Nemoto, Takahiro; Honda, Yuki; Tochio, Daisuke; Inaba, Yoshitomo; Sato, Hiroyuki; Nakagawa, Shigeaki; Sawa, Kazuhiro
Proceedings of 23rd International Conference on Nuclear Engineering (ICONE-23) (DVD-ROM), 7 Pages, 2015/05
To investigate the safety design criteria of heat utilization system for the HTGRs, it is necessary to evaluate the effect of fluctuation of thermal load on the reactor. The nuclear heat supply fluctuation test by non-nuclear heating was carried out to simulate the nuclear heat supply test which is carried out in the nuclear powered operation. The test data is used to verify the numerical code to calculate the temperature of core bottom structure to carry out the safety evaluation of abnormal events in the heat utilization system. In the test, the helium gas temperature was heated up to 120
C. A sufficiently high temperature disturbance was imposed on the reactor inlet temperature. It was found that the response of temperatures of metallic components such as side shielding blocks was faster than those of graphite blocks in the core bottom structure, which was significantly affected by the heat capacities of components, the level of imposed disturbance and heat transfer performance.
Sumita, Junya; Ishihara, Masahiro; Nakagawa, Shigeaki; Kikuchi, Takayuki; Iyoku, Tatsuo
Nuclear Engineering and Design, 233(1-3), p.81 - 88, 2004/10
Times Cited Count：4 Percentile：29.26(Nuclear Science & Technology)A High Temperature Gas-cooled Reactor is particularly attractive due to its capability of producing high temperature helium gas and its possibility to exploit inherent safety characteristic. To achieve high temperature helium-gas, reactor internals are made of graphite and heat resistant materials, its surroundings are composed of metals. The reactor internals of the HTTR consist of graphite and metallic core support structures and shielding blocks. This paper describes the reactor internal design of the HTTR, especially the core support graphite structures, and the program of an in-service inspection.
Kaneko, Tetsuji; Tsukatani, Ichiro; Kiuchi, Kiyoshi
JAERI-Tech 2004-035, 18 Pages, 2004/03
JAERI-Tech-2004-035.pdf:0.81MB
Fuel elements used in the Reduced-Moderation Water Reactor (RMWR) have the stacking structure consisting of MOX pellets and UO
blankets in a fuel rod in order to attain the high breeding ratio and high burn-up simultaneously. It is a characteristic of the fuel elements that there is high thermal stress caused by inhomogeneous linear power density along the longitudinal direction of the fuel rod in comparison with the present LWR fuels. For this reason, it is important to estimate local deformation behavior of the fuel cladding tube with temperature difference caused by MOX pellet and UO blanket. The testing machine was designed to investigate thermal-fatigue behavior under biaxial stress condition. The testing machine consists of the temperature distribution control unit, low cycle fatigue testing unit and internal pressure loading unit, it is also possible to conduct the simulation tests to investigate effects of pressure change with burn-up and longitudinal load change due to operation modes and restriction of fuel rods.
Shelley, A.; Kugo, Teruhiko; Shimada, Shoichiro*; Okubo, Tsutomu; Iwamura, Takamichi
JAERI-Research 2004-002, 47 Pages, 2004/03
JAERI-Research-2004-002.pdf:3.08MB
Neutronic study has been done for a PWR-type reduced-moderation water reactor with seed-blanket fuel assemblies to achieve a high conversion ratio, a negative void coefficient and a high burnup by using a MOX fuel. The results of the precise assembly burnup calculations show that the recommended numbers of seed and blanket layers are 15(S15) and 5(B5), respectively. By the optimization of axial configuration, the S15B5 assembly with the seed of 1000
2 mm high, internal blanket of 150 mm high and axial blanket of 4002 mm high is recommended. In this configuration, the conversion ratio is 1.0 and the core average burnup is 38 GWd/t. The S15B5 assembly can attain the core average burnup of 45 GWd/t by decreasing the height of seed to 5002 mm, however, the conversion ratio becomes 0.97. The void and fuel temperature coefficients are negative for both of the configurations. Effect of metal or T-MOX (PuO+ThO) fuel has been also investigated. Metal improves the conversion ratio but makes the void coefficient worse. T-MOX improves the void coefficient, but decreases the conversion ratio.
Tsukada, Takashi
Zairyo To Kankyo, 52(2), p.66 - 72, 2003/02
Irradiation assisted stress corrosion cracking (IASCC) is a potential failure mode suffered by the core-components of austenitic stainless steels in the aged light-water reactor (LWR), which is the intergranular type cracking caused by synergistic effects of neutron/gamma radiation and chemical environment. Effects of radiation on the materials and high-temperature water are discussed in this paper to understand IASCC phenomenon from a mechanistic viewpoint. It is essential to elucidate the radiation-induced microcompositional and microstructural changes in the alloy for mechanistic and predictive investigations of IASCC. Although grain boundary segregations of alloying and impurity elements are significant factors affecting IASCC, it has been considered that the radiation-induced microstructural and mechanical changes of materials play critical roles in IASCC. For mechanistic understanding of IASCC, further fundamental research works with experimental and theoretical approaches are needed. Efforts directed to the researches at the Japan Atomic Energy Research Institute are also described.
Hatae, Takaki; JT-60 Team
Proceedings of 6th Japan-Australia Workshop on Plasma Diagnostics (CD-ROM), 13 Pages, 2002/00
The main purpose of JT-60U project is to make contribution to establishment of scientific basis of ITER and the demo tokamak reactor. Our ultimate goal is to achieve and sustain high integrated performance, namely high beta, high confinement, high bootstrap current fraction, full non-inductive current drive and heat/particle control, in a reactor-relevant regime. Toward this goal, we have developed weak magnetic shear ("high 
mode") and reversed magnetic shear plasmas. In both regimes, the internal transport barrier (ITB) and the edge pedestal are obtained simultaneously. As a large-sized tokamak equipped with a variety of devices for heating, current drive and profile control, JT-60U has high ability to approach the conditions required in reactors (ITER or demo): low values of normalized Larmor radius and collisionality, high toroidal field, high temperature with Te
Ti, small central fueling, small ELM activities, etc. This paper reviews recent JT-60U results with the emphasis on the projection to the reactor-relevant regime.
Sukegawa, Takenori; Hatakeyama, Mutsuo; Yanagihara, Satoshi
JAERI-Tech 2001-058, 81 Pages, 2001/09
JAERI-Tech-2001-058.pdf:5.98MB
In general, neutron transport and activation calculation codes are used for residual radioactive inventory estimation; however, it is essential to verify calculations by measurement results because of geometrical complexity of the reactor and so on. The comparison between measured and calculated radioactivity in the JPDR core components showed a relatively good agreement (factor of 2), and it was cleared that water content and weight ratio of steel bars to concrete materials significantly influenced the neutron flux distribution in the biological shield (factor of 2-10 error). The measured radioactivity inside of the reactor pressure vessel wall and at the inner part of the biological shield was compared in detail with the calculations to verify the methodology applied to calculations of radioisotope production. Then it was found that the radioactive inventory could be estimated accurately with combination of calculations and measurement of radioactivity in samples and dose rate distribution for planning of dismantling activities.
Oka, Kiyoshi; Nakahira, Masataka; Kakudate, Satoshi; Tada, Eisuke; Obara, Kenjiro; *; *
JAERI-Tech 96-035, 47 Pages, 1996/07
no abstracts in English
Maruyama, So; Saikusa, Akio; Iyoku, Tatsuo; Shiozawa, Shusaku; *
Transactions of the 13th Int. Conf. on Structural Mechanics in Reactor Technology (SMiRT),Vol. I, 0, p.581 - 586, 1995/00
no abstracts in English
laserOka, Kiyoshi; Kakudate, Satoshi; Nakahira, Masataka; Tada, Eisuke; Obara, Kenjiro; *; *; *; Shibanuma, Kiyoshi; Seki, Masahiro
JAERI-Tech 94-033, 20 Pages, 1994/11
no abstracts in English
; ; Onodera, Junichi; ; Ikezawa, Yoshio
Proc. of the Int. Conf. on Radiation Effects and Protection, p.434 - 439, 1992/00
no abstracts in English
Onodera, Junichi; ; ; ; Ikezawa, Yoshio
Journal of Aerosol Science, 22(SUPPL.1), p.S747 - S750, 1991/00
no abstracts in English
; Hoshi, Tatsuo; Tachibana, Mitsuo
Low and Intermediate Level Radioactive Waste Management,Vol. 1, p.189 - 195, 1991/00
no abstracts in English
Tachibana, Mitsuo; Hoshi, Tatsuo; Miki, Ichiro
Proc. of the 1st JSME/ASME Joint Int. Conf. on Nuclear Engineering,Vol. 2, p.81 - 84, 1991/00
no abstracts in English
Yanagihara, Satoshi; ; Nakamura, Hisashi
Nuclear Technology, 86, p.148 - 158, 1989/08
Times Cited Count：12 Percentile：77.45(Nuclear Science & Technology)no abstracts in English
; ; ; ; ; Sanokawa, Konomo
JAERI-M 85-056, 18 Pages, 1985/05
no abstracts in English
